Just How to Replace a Bath Tub
Just How to Replace a Bath Tub
Blog Article
Are you currently hunting for answers concerning A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is likewise a reasonably tough task. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old tub as well as place the new bath tub, the job is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Ensure you have certified on your own for the job and also are comfortable attempting it. Instead of hiring a specialist to take control of a halfway-completed project, it is far better to consider using one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This write-up will aid you install a brand-new bathtub in your shower room if you have currently bought a brand-new bathtub as well as do not need to transform the arrangement of your previous water system pipelines.
Your devices and material list need to comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The procedure of removing the existing taps can be fairly bothersome due to the restricted accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipes. Once the supply pipes have actually been eliminated, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing substance.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in place with the producer provided backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap connectors. The previous type needs to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the required setting. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water as well as examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as likewise examine the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait till the bathtub has been made use of at the very least once as this will certainly resolve it into its final placement.
Preparing for the Setup
To start with, the supporting framework provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use all of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing difficulties with moisture as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes and cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently offered on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that piece of content was important. Liked our content? Please share it. Let somebody else find it. I truly appreciate reading our article about Installing A Bathtub.
Click Report this page